artemis Shop/Brackets products

Super Post DV Pro MD 595,00 €

Shooting high mode and low mode, no problem when the super post for the artemis DV Pro MD is available.

Thanks to the modular design of the artemis DV Pro MD, changing from the standard post to the longer super post can be done in minutes. This unique feature makes the DV Pro MD to outstanding system is this class.

Not only the maximum length of 95 cm (37.4“) makes the super post interesting, even its shortest length of 62 cm (24.4“) is a great alternative to the standard post. A „short“ super post makes it much easier to balance even quit heavy cameras. Because of the additional length of the super post the existing amount of counterweight (monitor and battery) will be used more efficiently. When the super post is used, the overall weight stays lower even when the weight of the camera is increasing. More smoothness and stability will be also added to the rig when a super post is used, what is another nice side effect.

To increase the height of the camera in high mode, it is helpful to use the 10“ arm post, the longer arm post will lift the rig another 12 cm (4.72“).

Or the other way around, to bring the camera lower in low mode it is very helpful to use the D-Bracket for the DV Pro, the bracket will lower the rig about 20 cm (7.87“).

To make balancing even faster and easier use extra counterweights like the Donuts (6892) and the additional weights for the monitor (4967).

Outer diameter: 24mm (0.94“)

Inner diameter: 20mm (0.79“)

Minimal length: 62 cm (24.4“)

Maximal length: 95cm (37.4“)

Post Tool 77,35 €

The post tool is the right tool to disassemble the the side to side module and the lower sled from the 1.5" post. Also the post tool will be used to adjust the self centering ring of the 1.5" gimbal.
For all artemis with 1.5" center post

6 mm Hex Key 1/4" 11,90 €

6 mm - 1/4" hex key to adjust the angle of the ACT2 spring arm.

Sideload Plate S 63,07 €

Camera dovetail plate including a 1/4" camera screw
Dimensions 140 x 50 mm / 5.5 x 2 in
Weight: 120 gr. / 4.2 oz
Aluminium alloy, matte black surface
Also recommended for DV 1, FSB 2, FSB 4, FSB 6 and FSB 8

CFAST artemis 101,15 €

To mount the C-Motion focus remote receiver at the artemis Focus Barcket (6530), the adapter is needed. It allows to mount the receiver straight or pointing to the side.

Extension Unit for Rods / EU 15 89,25 €

Extention unit � 15:15mm / with short rod � 15 mm EU15

Euro Mount Adapter f. Hard Mount 208,25 €

To fix the hard mount (6819) in a car or van, or on a pick-up, this adapter can be used. Use a wooden platform, mount the adapter with 8 screws on the platform and attache the hard mount. Because this adapter is using the Euro Mount all kind of bazookas and other accessories can also be used with this adapter.

Recorder Bracket 279,65 €

This Recorder Bracket is made to be used with the artemis Cine HD Pro, Cine HD or Cine. It can be mounted with four screws at the backside of the lower sled. The platform will take harddisc recorders, video transmitter or a small TFT monitor for the return video. There is a wide range of things can be mounted on this platform.

Telescopic Monitor Arm for EFP Pro HD SDI only 577,15 €

This version of the artemis monitor bracket is mounted directly at the center post of the artemis EFP Pro HD SDI.
The outstanding features of this monitor braket are:
No-tool adjustments: all length and angle adjustment can be done with out any tools.
Telescopic design. The bracket allows free positioning and adjustment about the monitor distance to the center post.
The right position of the monitor is a essential condition for a perfect Dynamic Balance.
Pivoting rosette: The design of the artemis monitor bracket allows tilting the bracket close to 180� up and down. This allows to make the weight of a TFT monitor much more effective, because the center of gravity of the monitor will be closer to the level of the batteries. Which also provides a better dynamic balance. Only the artemis monitor bracket allows this adjustments.
The artemis bracket is a inherent part of the artemis EFP HD SDI systems. This bracket can be upgraded with the 1.5“ center post clamp (6613). This allows more flexibility in balancing and operating the EFP Pro HD SDI.

Arm post 3"" - � 5/8"" 29,75 €

Arm post made for artemis D-Bracket and all other brackets using a 5/8“ (15.8 mm) diameter, like GPI George Paddock, Steadicam EFP and others.
Dimensions: � 5/8" (15.8 mm), length 3" (76 mm)

Arm post 10" - � 5/8" 41,65 €

Arm post made for artemis ACT2 spring arm and all other arm using 5/8“ (15.8 mm) diameter, like GPI George Paddock, Steadicam EFP and others.
Dimensions: � 5/8" (15.8 mm), length 10" (254 mm)

Camera Off Center Adapter 178,50 €

This extra wide camera mounting adapter plate, with 3 vents allows to mount the camera off set, by using 3/8” camera mounting screws. This will help to optimize the center of gravity and to balance cameras like the Sony HDV much faster. The adapter also offers two M5 threads on both ends to mount Chrosziel light weight support.
Length: 120 mm / 4.72“ - Wide: 100 mm / 3.93“

ACT2 Docking Bracket 1.8"/1.5" 892,50 €

The new artemis ACT2 Docking Bracket, focusing on, easy handling, maximum safety and maximum functionality. The symmetric design allows the same easy use for left or rig handed operators.
The self locking clamp mechanisms guarantees a secured stay of the rig in the docking bracket.

The pivoting tool bar allows to store tools, arm posts and the post tool. Because of the ambidextrous design of the bracket, the tool bar can be on both sides of the bracket.
The two balance pins on top of bracket make it easy and safe to move the rig from the docking up to the from balance pin. The balance pin at the back of the telescopic top rod, is made for spin tests, double checking the dynamic balance.

ACT2 Docking Bracket to be used with systems using the 1.8" post and small docking ring.

This bracket will be needed when an older artemis rig had been upgraded with the new 1.8" post / for C-Stands with 5/8" spigot for Cine HD , Cine, EFP HD SE, EFP

Counterweight small artemis DV 29,75 €

Counterweight for the artemis Handheld system, with 67 gr (2.4 oz)

Monitor Mount / artemis Handheld 65,45 €

Monitor mounting bracket for the Handheld system, for monitors up to 7" diagonal

Counterweight heavy artemis DV 41,65 €

Counterweight for the artemis Handheld system, with 270 gr (9.6 oz)

Counterweight medium / artemis Handheld 35,70 €

Counterweight for the artemis Handheld system, with 135 gr (4.7 oz)

V-Mount Camera Plate 833,00 €

The Sony V-mount snap plate is designed to work with all V-mount cameras. The extreme lightweight plate, only 405 gr / 0,89 lb, has been specifically crafted to offer the most secure connection between the camera and plate.

For Cine HD Pro, Cine HD, Cine, EFP Pro HD SDI, EFP HD SE

C-Stand Turtle Base 202,30 €

Century-Stand with detachable turtle base with a � 15.8 mm / 5/8“ stud. Maximum height 155 cm / 61". The detachable base (turtle base) makes it easy to transport the C-Stand in the artemis case or trolly.
Steel / silver

15mm Rod Bridge Adapter 65,45 €

The slim 15mm rod bridge, supporting a perfect positioning and fixation of focus motors on 15mm rods. This bridge is much slimmer than the regular designs. This makes it possible to mount two bridges the same time sidewise at the motor. This is the best way to mount a focus-motor absolut torsion-free. This is a perfect additional for a light-weight-support.